Skip to content
CHANGHONGINDUSTRIAL FILTRATION Request a Quote

Filter Vessel Sizing: How to Choose a Stainless Steel Housing

Filter vessel sizing starts with the process, not a catalog number. Before choosing a stainless steel housing, record the liquid, the required flow, the filter format and the installation limits that the housing must meet. This checklist helps an industrial buyer prepare a configuration request without treating a nominal size as a guaranteed capacity.

1. Define the duty before choosing a vessel size

Write down the normal flow and the peak flow separately. A housing that is acceptable at a normal rate may not be suitable for a short peak, a start-up condition or a change in liquid viscosity. Also identify whether the duty is liquid filtration, gas filtration, bag filtration or cartridge filtration. The filter format changes the internal arrangement and the information a supplier needs to confirm.

Record the liquid, temperature, pressure, solids load and the result you need from filtration. For example, a particle-control duty, a polishing step and a prefilter can require different media and change-out decisions. A micron number alone does not size the vessel. If the acceptance requirement is still being developed, describe the application and the expected contaminant instead of inventing a rating.

2. Match the housing to the filter format

QD stainless steel housings are listed for 304 or 316L construction and can be configured for cartridge, bag and gas filtration. Those options should be treated as separate configuration paths. A cartridge housing may depend on cartridge length, count and end connection; a bag housing uses a different internal support and sealing arrangement. Confirm the format before comparing dimensions or prices.

When the filter element is already known, send the existing element type, length, outside diameter, end connection and a photo of the label or assembly. If the element is not known, the filter selection guide can help organize the missing information. The earlier bag and cartridge buying guide explains the format decision; this article focuses on the housing configuration after that decision.

3. Check connections, space and operating limits

List the inlet and outlet connection type and size, the preferred orientation, the available installation height and the space needed to remove the cover or element. These details often determine whether a housing can be installed even when its filtration duty appears correct. Include drain, vent, clamp or flange requirements when they matter to the existing line.

Ask for confirmation of the housing’s operating pressure and temperature for the stated service. Do not transfer a pressure or temperature value from one model to every configuration. Seal material, internal parts and connection choices can affect the final selection, so the quotation should identify the complete configuration rather than only the shell material.

4. Use a simple sizing request

Information to provide Why it matters
Normal and peak flow Sets the duty that the housing must handle and makes peaks visible.
Liquid or gas and temperature Supports material, seal and operating-limit review.
Cartridge, bag or gas format Determines the internal arrangement and replacement path.
Element dimensions or existing housing Checks fit, length, count and change-out space.
Inlet, outlet and installation space Checks connection and maintenance compatibility.
Required quantity and target duty Lets the supplier return a configuration that can be compared.

This list is a quotation starting point, not an engineering calculation. If a value is unknown, mark it as unknown and explain the application. A clear unknown is safer than a guessed flow-per-cartridge number.

5. Compare a quotation by the whole configuration

When two housing quotations look similar, compare the material, filter format, element length and count, connections, seals, operating limits and included accessories. Then check whether the proposed arrangement fits the existing line and the intended change-out method. The lowest shell price does not by itself establish the lowest operating cost or the best filtration result.

For cartridge terminology, the string-wound and polypropylene selection guide explains why construction and media should be recorded separately. That distinction also helps prevent a housing request from mixing a cartridge material with a vessel requirement.

What to send for a QD housing inquiry

Send the product format, flow, fluid, temperature, pressure, connection details, existing element dimensions and required quantity. If the specification is incomplete, describe the process and upload a photo. You can review the QD stainless steel housing options and then request a configuration quotation. The supplier can confirm which details are still needed before a final configuration is selected.

String Wound Filter vs Polypropylene: A Cartridge Selection Guide

A string wound filter vs polypropylene comparison starts with a naming problem: string wound describes how a cartridge is constructed, while polypropylene, or PP, describes a material. A string-wound cartridge can itself use polypropylene yarn. Before comparing quotations, identify whether the alternative is a melt-blown PP cartridge, a pleated PP element, or another construction.

For industrial liquid filtration, the useful comparison is between two specified cartridges in the same duty. This guide explains how to turn an unclear “wound or PP?” request into a quotation that can be reviewed. If you have not yet chosen between bags and cartridges, use the bag and cartridge buying guide first.

Identify the construction on each quotation

A string-wound element uses yarn wrapped around a supporting core. A melt-blown element uses a fibrous structure formed through the melt-blowing process. Those descriptions help identify the product; they do not establish a universal winner for service life, pressure drop or removal efficiency.

Ask the supplier to fill in separate entries for media material, construction and core. “Polypropylene cartridge” is incomplete because it leaves the construction unspecified. Likewise, “string wound” does not identify the yarn or core material.

Entry on an offer What still needs confirmation
PP filter cartridge Whether the element is wound, melt-blown, pleated or another construction.
String-wound cartridge The yarn, core, dimensions, end arrangement and rating basis.
Melt-blown cartridge The specific series, media, core configuration and connection details.
Same length and micron rating Physical fit, documented filtration performance and operating limits.

Separate the available series and their options

CHANGHONG’s XPP string-wound cartridges list polypropylene yarn and cotton ordering options, with polypropylene or 304 stainless steel cores. Published outer diameters are 63 and 115 mm. These are selection options; the required combination still needs confirmation for the actual liquid and installation.

The RPP/RJP polypropylene cartridge range distinguishes RPP melt-blown construction from RJP melt-blown wrapped construction. Do not carry a surface, core or connection option from one series onto the other without confirmation.

A request for PP media therefore does not eliminate the wound option. Conversely, a preference for a wound structure does not mean cotton is automatically suitable for the fluid. Keep the material decision and the construction decision visible in the specification.

Check housing fit before treating a cartridge as a replacement

Use the existing element and housing documents to record the overall length, outer and inner diameters, end arrangement and sealing details. Photograph both ends of the removed element when drawings are unavailable. A photograph can help identify an arrangement, but it should not substitute for measurements or a confirmed configuration.

A nominal length alone is insufficient. For example, both product ranges list 9.75-inch and 10-inch options. Treat those as separate listed sizes until the housing requirements establish which is appropriate. Do not assume that similar appearance or a shared nominal size proves interchangeability.

Request a written fit confirmation against the supplied dimensions and housing information before purchasing replacements. The selection checklist provides a place to organize the fluid, duty and installation details.

Compare performance under the stated conditions

Ask both suppliers for the meaning of the quoted rating, the supporting test information and the conditions covered by their data. A shared micron number is not enough to show equivalent retention. Keep any performance claim attached to the exact cartridge being quoted.

For a flow comparison, state the liquid, temperature and required flow, and request the corresponding pressure-drop information. For operating limits, ask about the complete element, including its core and end components. Do not transfer a temperature or pressure limit from one material name to every cartridge that uses it.

If a supplier proposes a replacement trial, agree on the acceptance criteria before installation. Record the candidate configuration and the process conditions, then assess the required downstream result and operating behavior. A claim of longer life is not a purchasing basis unless the comparison uses a defined duty and a clear endpoint.

Send a comparison request that suppliers can answer

A useful request contains the existing part reference if known, photographs or dimensions, liquid and operating conditions, required rating and quantity. Add the problem prompting the change: uncertain fit, an unclear specification, an operating issue, or a request to evaluate another construction.

For example: “Please compare a PP-yarn wound cartridge and a PP melt-blown cartridge for the attached housing and duty. Identify each proposed configuration, confirm fit, and provide the rating basis and applicable operating limits.” This is an example inquiry, not a claim that either configuration suits an unspecified process.

Keep the supplier’s answers in a side-by-side record. Mark missing information as pending and resolve it before approving the replacement. Use the technical resources to organize documentation requests, or send the existing cartridge details for selection support.

Bag Filter vs Cartridge Filter: A Liquid Filtration Buying Guide

Choose a bag or cartridge filter by the required liquid quality, the element’s documented performance, and the housing it will fit. The words “bag” and “cartridge” describe different element formats; they do not, by themselves, establish removal efficiency, service life, or the correct vessel size. For a useful quotation, compare complete configurations under the same operating conditions.

This guide covers industrial liquid filtration. It does not compare dust collectors, HVAC pocket filters, or pool filtration systems. Use it to prepare a new installation or to decide what information is missing before replacing an existing filter.

Start with the element format and the existing housing

A liquid filter bag is a flexible filtering element installed with a compatible support and sealing arrangement. A cartridge is a separate element whose dimensions and end connections must match its housing. Cartridge construction is not limited to pleated media: melt-blown and string-wound designs are also available.

CHANGHONG’s industrial liquid filter bag range and melt-blown and string-wound cartridges illustrate these different formats. They are product families to investigate, not interchangeable replacements.

If a vessel is already installed, identify its model and internals before selecting the consumable. A bag’s opening and support arrangement are different matching questions from a cartridge’s length, end cap, and seal. A similar-looking stainless steel shell is not evidence that either format will fit.

Bag filter vs cartridge filter: compare these five items

Comparison Bag configuration Cartridge configuration
Mechanical fit Confirm bag dimensions, opening, seal, and support. Confirm length, diameters, end caps, seals, and element count.
Particle removal Request the rating basis and performance evidence for the selected bag. Request the same evidence for the selected cartridge construction.
Material review Identify media, seams or joints, opening components, and seals. Identify media, core, end caps, joining materials, and seals.
Operating duty Review the proposed bag-and-housing combination at the actual flow and fluid conditions. Review the proposed cartridge-and-housing combination on that same basis.
Replacement cost Include the number of bags, labor, retained liquid, and disposal. Include every cartridge changed, labor, retained liquid, and disposal.

Make the micron specification comparable

A request for a “10-micron filter” leaves several purchasing questions unanswered. Is the rating nominal or absolute? What removal efficiency is claimed at the stated size? Which test method and conditions support it? Does the evidence cover the proposed finished element or only its media?

Put those questions on both quotations. If one supplier provides a stated rating without its basis while another provides test information, the two offers are not yet an equal comparison. Do not resolve the gap by assuming that every cartridge is finer than every bag.

Also describe the result you need downstream. For example, are you protecting equipment from particles, reducing visible contamination, or meeting a defined process acceptance criterion? A photo or an existing filter label can start the discussion, but it does not replace the required performance specification.

Check operating limits separately from purchase price

Send normal and peak flow, liquid composition, concentration, viscosity where known, temperature, and operating pressure. Ask for the proposed configuration’s clean pressure drop and permitted differential pressure. Keep the vessel’s pressure rating and the element’s differential-pressure limit as separate entries in the review.

The U.S. EPA’s bag and cartridge filtration guidance, Chapter 8, describes the relationship between particle accumulation, pressure drop, and replacement, and notes that flow, incoming water quality, and filter material affect replacement intervals. That document addresses drinking-water treatment; it is not a qualification certificate for an industrial chemical application or a CHANGHONG product.

For your process, obtain the selected configuration’s limits rather than borrowing a change-out pressure from an unrelated installation. Record upstream and downstream pressure at an agreed operating flow, then assess the readings against those limits and the required filtrate quality. A pressure reading alone does not establish that the liquid meets its acceptance criterion.

Compare the cost of a change-out, not one consumable

A lower unit price can be misleading when the quotations contain different quantities of elements. Use a simple worksheet:

Cost per change-out = consumables replaced + labor + downtime cost + discarded process liquid + disposal.

For a purely illustrative example, suppose one proposed configuration uses a $12 consumable and incurs $18 of other change-out costs. Another uses a $20 consumable and incurs $10 of other costs. Both total $30 per change-out. These are hypothetical numbers, not CHANGHONG prices or predicted operating results.

To compare cost per batch or per volume processed, you still need the actual number of change-outs and acceptable output over the same period. A trial record can supply that evidence. Avoid declaring a winner from the consumable price while leaving replacement frequency unknown.

What to send for a housing and element quotation

For a new system, ask the supplier to identify the element format before finalizing the housing. For an existing system, begin with its nameplate, an internal photograph, and measured element dimensions. CHANGHONG’s QD stainless steel filter housings include different configurations; cartridge dimensions and counts do not describe every bag or gas configuration in the series.

The filter selection and model-matching checklist helps organize these details. If a value is unknown, mark it as unknown and describe the application. Do not copy an operating limit from another model merely to complete the form.

Questions buyers often ask

Can a cartridge replace a bag in the same housing?

Only after the complete arrangement has been checked. The support, sealing surfaces, dimensions, and flow path need to suit the replacement. Treat a change of element format as a configuration review, not an automatic drop-in substitution.

Which option lasts longer?

There is no established answer for an unspecified liquid and element. Request comparable operating data or agree on a trial that records flow, pressure difference, processed volume, change-out reasons, and filtrate acceptance. Keep an unverified service-life estimate separate from measured results.

Should a bag always come before a cartridge?

Do not add a stage solely because the formats are different. First identify what the proposed upstream stage must remove and what the downstream stage still needs to achieve. Ask for the basis for the arrangement, its pressure requirements, and how each stage will be maintained.

Turn the comparison into a usable inquiry

Start with the liquid and the result you need, then attach the available model details, dimensions, or photographs. You can request a QD housing configuration review even if some specifications are still unknown. For drawings and other selection material, return to Technical Resources.